Export practical guide
Choosing a container for Africa: 20 ft, 40 ft, high cube, open top or flatrack
Containers are often chosen out of habit: a 20 ft box for a small consignment, a 40 ft one for a large one. For project equipment going to Africa, that habit overlooks the two constraints that usually decide the matter. One is weight, which limits a container long before volume when the cargo is steel or machinery. The other is the journey after the port, often by road all the way to site.
This guide relies on the technical specification published by the carrier Hapag-Lloyd, which follows the ISO 668 standard, and on the Belgian container weighing rules published by the Federal Public Service Mobility.
Updated on 21 October 2026
What really fits in a 20' or a 40'
ISO 668 sets minimum internal dimensions of 5,898 mm in length for a 20', 12,029 mm for a 40' and 2,350 mm in width. Height is 2,350 mm for a standard 8' 6'' box and 2,667 mm for a 9' 6'' high cube. Hapag-Lloyd's nominal figures are slightly larger: a standard 20' gives 33.2 m³, a 40' 67.7 m³ and a 40' high cube 76.3 m³.
These are internal dimensions, not clearances: a crate must also pass through the doors, which are narrower and lower than the interior. Before booking, measure every packed crate rather than the bare equipment, and leave space for bracing.
Weight runs out before space
Hapag-Lloyd gives a maximum gross weight of 32,500 kg for standard containers, whether 20' or 40'. After tare, payload is 30,200 kg for a 20' and 28,800 kg for a 40', so the larger box, being heavier when empty, carries less. For tools, pipework or machine parts, the 20' is often the sensible choice.
The load also has to be spread. Hapag-Lloyd quotes a maximum of 4.8 tons per running metre in a 20' and 3 tons in a 40', and a floor rated for a forklift with an axle load of no more than 5,460 kg. A heavy machine on a small footprint needs timber bearers to spread the load. Finally, the sea limit is not the road limit: the carrier refers customers to its local office for road and rail limits, which need checking for the leg from the port of arrival to site.
Open top and flatrack for cargo that sticks out
A piece that is too tall, too wide or must be lifted in by crane will not go through the doors of a closed box. Hapag-Lloyd designs open top and hardtop containers for over-height cargo, heavy loads and loading through the roof. The flatrack, with no sides or roof, takes heavy and out-of-gauge cargo, up to 60,000 kg gross for a 40'. A high cube gains height but can itself become over-height for some bridges inland.
This is the kind of question a complete workshop raises: for a private company in Nigeria, Sobetracom supplied high-capacity equipment including a press brake of up to 10 m and overhead cranes. For machinery like this, length, centre of gravity and lifting points are collected from the manufacturer before any booking is made.
Weighing before loading at Antwerp
According to the Belgian FPS Mobility, any container loaded onto a ship covered by the SOLAS convention must have a verified gross mass (VGM), and the shipper is responsible for it. The VGM document goes to the master and the terminal before loading, because the stowage plan depends on it. 2 routes are accepted: weighing the packed container on calibrated equipment, or calculating it under a method certified through ISO, AEO or approval by the Directorate-General for Shipping. Maersk points out that VGM includes dunnage and bracing as well as the tare shown on the container plate.
Sobetracom gathers this data with the manufacturer (packed dimensions, weights, lifting points) and passes it to the buyer's forwarder, who books the right equipment. Road load limits vary by country and corridor, so the forwarder and the destination broker should confirm what can legally travel to site before the final choice.
Frequently asked questions
- A 40' often costs little more than a 20', so why not always book one?
- Because its payload is lower: 28,800 kg against 30,200 kg at Hapag-Lloyd. For heavy equipment, a half-empty 40' at maximum weight gains nothing, and it is harder to manoeuvre on some roads and sites.
- Who supplies the VGM when the buyer has appointed the forwarder?
- The shipper, meaning the party named as shipper on the transport document. Under FCA or EXW, agree in writing who weighs the container and who sends the document to the terminal.
- Does a high cube go everywhere?
- Not necessarily. Hapag-Lloyd warns that its height must be considered for inland transport because of bridges and clearances. The forwarder should check the whole road route to site.
Sources
- Hapag-Lloyd, « Container Specification » (October 2026)
- SPF Mobilité et Transports, « Containergewicht (VGM) » (August 2026)
- Maersk, « Verified Gross Mass » (October 2026)
- Sobetracom, références clients (September 2026)
This page summarises public sources as of the date shown. It does not replace the official text: check it before committing to a purchase, a bid or a shipment.
