Sobetracom

Equipment sourcing · IT and broadcast

Buying a DTT transmitter for Africa: DVB-T2, emission mask and power

In Africa, digital terrestrial television follows a regionally agreed timetable. According to the ITU, the 17 June 2015 deadline for switching off analogue television in the UHF band applied to every country in Region 1, Africa included, under the GE06 agreement of 2006. Many networks are still being built out or densified site by site, and each new transmitter has to fit into that frequency plan.

A DTT transmitter is a demanding technical purchase: power, emission mask, modulation standard, cooling, power supply, antenna and remote monitoring all have to be specified together. This guide sets out the ETSI standards used as references and the site conditions that matter on African networks.

Updated on 21 October 2026

Broadcast standard: DVB-T2, matched to receivers

ETSI EN 302 755, version V1.4.1 of 2015-07, describes DVB-T2, the second-generation system for digital terrestrial television. Before ordering a transmitter, confirm the standard and video coding adopted by the country, since viewers' TV sets and set-top boxes have to follow. In the DR Congo, the Bureau Veritas pre-shipment verification sheet lists a ban on importing TV sets that do not comply with DVB-T2 and MPEG4, under interministerial order No. 002/TNT/CAB/MCM/LMO/2015.

The specification should therefore state the modulation standard, the intended network mode (single or multi-frequency), the multiplex input interface and compatibility with the existing headend.

Power class and emission mask under ETSI EN 302 296

The harmonised standard ETSI EN 302 296 V2.2.1 combines a power class and an emission class. A class H transmitter delivers at least 25 W in VHF (174 MHz to 230 MHz) or UHF (470 MHz to 694 MHz); below that it is class L. Emission classes run from 0, a non-critical mask taken from the RRC-06 conference, to 3, critical ACLR limits. An H0 unit, for instance, is a high-power transmitter with a non-critical mask.

The mask depends on the site: near a border or an occupied adjacent channel, a critical mask protects neighbours and eases the coordination the GE06 plan requires. Stating the required category in the tender lets buyers compare output filters, often the item that separates two offers.

Site, power and cooling

The ITU points out that digital needs less energy than analogue for the same coverage. Even so, a transmitter runs around the clock, often on an isolated hilltop. According to the World Bank Enterprise Surveys, 77.4% of firms surveyed in the DR Congo in 2024 experienced power outages, so backup power, a generator or solar belong in the project. The ETSI standard applies its requirements within the environmental profile of the intended use, so the tender should state ambient temperature and dust at the site, the cooling method (air or liquid), amplifier redundancy and IP remote monitoring to cut site visits.

What we compare for the buyer

From Belgium, Sobetracom puts one specification to several transmitter manufacturers: output power and EN 302 296 category, overall efficiency, redundancy, cooling, filter, interfaces and supervision. We ask for documentation, the recommended spare parts list and the technician training plan. In Guinea, our relays supported a supply of professional broadcast equipment for television. Import arrangements and frequency authorisations are then confirmed with the regulator and the licensed customs broker.

Frequently asked questions

Should the transmitter and antenna come from the same supplier?
It is not compulsory, but single responsibility for transmitter, filter, feeder and antenna simplifies acceptance and warranties. If the lots are split, interfaces and performance at the output point must be defined precisely.
Can an ETSI-compliant transmitter be installed outside Europe?
ETSI standards are a widely used technical reference, but frequency, power and site still need authorisation in the destination country and must fit the coordinated frequency plan. Those authorisations should be sought before the firm order.

Sources

  1. UIT, communiqué de presse 2015/19 (June 2015)
  2. ETSI EN 302 296 V2.2.1 (June 2021)
  3. ETSI EN 302 755 V1.4.1 (July 2015)
  4. Bureau Veritas, fiche « Pre-export verification of imports for the Democratic Republic of Congo », Rev. 26 (June 2024)
  5. Banque mondiale, World Development Indicators (Enterprise Surveys), indicateur IC.ELC.OUTG.ZS, RD Congo (October 2026)
  6. Sobetracom, références clients (September 2026)

This page summarises public sources as of the date shown. It does not replace the official text: check it before committing to a purchase, a bid or a shipment.

A project in Africa? Let's talk.

Tell us what you need and where it goes. We come back to you with first leads.