Sobetracom

Import guide · Burundi

Certificate of conformity for Burundi: the BBN's PVoC explained for buyers

Burundi checks the conformity of imports before they leave the country of export. The Burundi Bureau of Standards and Quality Control (BBN) runs a Pre-Shipment Verification of Conformity programme, known as PVoC, and has contracted SGS to carry it out. Regulated goods arriving without a certificate of conformity cannot clear in the normal way.

For a public buyer or an NGO ordering pumps, pipes or electrical equipment in Europe, the matter is therefore settled at the supplier's premises rather than in Bujumbura. This guide sums up what the BBN and SGS publish: who does what, the certification routes, the products covered and the exemptions.

Updated on 20 October 2026

Standards from the BBN, inspection by SGS

According to the BBN, the government entrusted verification to SGS under a contract that began on 15 March 2014, with the BBN, as custodian of standards, administering the programme. Certification rests on Burundian standards or approved specifications. SGS notes that national standards prevail, though regional and international standards such as IEC, ISO or EN are accepted where requirements are met.

Checks continue on arrival. BBN inspectors are posted at the port of Bujumbura and at the Kobero border. They verify the certificate of conformity (CoC) for SGS-covered goods, the quality mark for goods of EAC origin, and carry out a physical inspection.

Routes A, B and C: a matter of shipment frequency

The 2025 SGS flyer describes each route. Route A covers suppliers without regular shipments and sensitive products: inspection, testing where needed, then a CoC per consignment. Route B is for regular suppliers with registered products, registration being renewed annually. Route C is for manufacturers holding a product licence. The 2015 SGS guide added that at least 3 shipments under Route A are needed before moving to B or C.

Testing takes place in SGS laboratories, in a third-party laboratory accredited to ISO/IEC 17025, or at the manufacturer if it can show a quality system and calibrated equipment. A one-off project tender will nearly always fall under Route A.

The fee, and the cost of going without

SGS fees are a percentage of FOB value: 0.50 % on Route A, 0.45 % on Route B and 0.25 % on Route C, with a minimum of 235 USD and a cap of 2375 USD per certificate. The exporter pays before inspection, and testing and container sealing are extra.

Shipping without a CoC is costlier. The SGS guide refers to penalties of 15 % of CIF value for goods imported without inspection, and the 2025 flyer states that the supplier bears the economic consequences of goods shipped without a certificate. A non-conformity report can also stop the consignment from leaving for Burundi.

Products covered, exemptions and water projects

The SGS product list covers much of the tariff: plastic pipes (heading 39.17), steel tubes and fittings (73.04 to 73.07), machinery in chapter 84 and electrical equipment in chapter 85. Listed exemptions include consignments under 2.000 US dollars, pharmaceuticals, donations from foreign governments or international bodies to the Burundian administration or recognised humanitarian organisations, and EAC goods bearing a quality mark.

This matters for water supply schemes. In Burundi, Sobetracom supplied around 10 km of hydraulic piping, fittings and tools for CASOBU, financed and supported by AMU: product families that appear on the programme's list.

Frequently asked questions

Does donated equipment for a Burundian NGO need a PVoC certificate?
The SGS guide exempts donations from foreign governments or international bodies to the Burundian administration and to recognised humanitarian organisations. A purchase funded by a project but invoiced in the ordinary way may not qualify, so SGS should confirm the position before dispatch.
Who applies for the certificate, the buyer or the supplier?
The exporter files the request for certification with SGS, with a pro forma invoice, quality documents and test reports, naming the point of entry into Burundi. Sobetracom handles that file on the supplier side and arranges the pre-loading inspection, and its relays in Burundi make sure the CoC travels with the clearance papers. As the product list and exemptions partly date from 2015, a check with SGS and the licensed clearing agent is still needed before each shipment.

Sources

  1. Bureau Burundais de Normalisation et Contrôle de la Qualité (BBN), Contrôle importations (October 2026)
  2. BBN, Programme PVOC (October 2026)
  3. SGS, Burundi pre-shipment verification of conformity program (2025) (2025)
  4. SGS, Guide pour les opérateurs, Burundi, Vérification de la conformité des produits avant expédition (PCA) (March 2015)
  5. SGS, Liste de produits Burundi, Service de Vérification de la Conformité des Produits à la Commande et aux Normes avant Embarquement (March 2015)
  6. Sobetracom, références clients (September 2026)

This page summarises public sources as of the date shown. It does not replace the official text: check it before committing to a purchase, a bid or a shipment.

A project in Africa? Let's talk.

Tell us what you need and where it goes. We come back to you with first leads.