Sobetracom

Equipment sourcing · Water and infrastructure

Water well drilling equipment for Africa: rig set-up, tooling, casing and screens

Buying drilling equipment is rarely about one machine. A rig produces no borehole without a compressor or mud pump, rods and bits of the right diameter, a support truck and water supply, and casing and screens suited to the geology. An incomplete set stands idle on its first site, often days from the nearest dealer.

This page helps a utility, ministry or NGO put together a coherent purchase. It draws on the drilling supervision guide published by the Rural Water Supply Network (RWSN), a plastic pipe industry note on PVC casing and UNICEF's toolkit for borehole procurement.

Updated on 20 October 2026

Assembling the complete unit

The RWSN guide gives an example of basic equipment for a programme of 10 boreholes: 1 drilling rig, 1 compressor, 1 mud pump, 1 water tanker and 1 support truck, enough rods for the deepest hole, bits of the right diameter, casing, gravel pack and drilling mud. The crew comprises a drilling manager, hydrogeologist, rig operator, driver, mechanic and 3 rig assistants.

That list is a framework for the tender. For each item, the specification sets target depth, drilling diameters, compressor output and pressure, carrier (truck or crawler) and accessories. It also asks for wear parts, consumables for the first campaign and manufacturer training for the driller and mechanic.

Drilling method and fluids follow geology

The RWSN guide pairs each method with its fluid. Down-the-hole hammer uses compressed air, possibly with water or foam: the hard-rock method, which needs a powerful compressor. Rotary drilling uses mud, water with additive, and suits unconsolidated formations. Percussion usually uses no fluid. The guide notes that bentonite is banned in some countries because it can permanently damage the aquifer, and recommends biodegradable polymers, so the additive should be checked with the national water authority.

Geology also sets the depth to equip for. On the West African basement, fresh rock is usually within 60 m and the weathered zone rarely exceeds 30 m; in East and Southern Africa it can reach 100 m. A unit intended for several regions should therefore cover both methods or target the one most common in the project area.

Casing and screens: diameter, material, stiffness

Casing stops the borehole collapsing; screens let water in while holding back sediment. According to the RWSN guide they are made of galvanised steel, PVC, glass-reinforced plastic or even bamboo, most often PVC or steel depending on depth and water corrosiveness. A 100 mm casing takes a handpump; for a motorised rural borehole 150 mm is generally enough, and diameter should be checked against the pump maker's curves. The guide allows 3 to 6 metres of sump below the screen and, for a handpump well, at least 5 metres into the aquifer. Screens are ordered with a slot size matched to the gravel pack, for example 0.75 mm or 1 mm.

For PVC, PIPA note POP105 points out that what matters in casing is stiffness, which depends on wall thickness: at the same pressure class, PVC-M or PVC-O does not replace PVC-U. PVC-O, which cannot be solvent welded, is not recommended. The Australian reference requires PVC-U, a minimum 100 mm diameter, PN9 for shallow low-yield bores and PN12 elsewhere. PVC casing and screens must also be stored out of the sun, which makes them brittle.

Buying and supervising

UNICEF's toolkit for planning, contracting and managing borehole drilling covers borehole procurement, equipment supply and supervision contracts. It builds on the RWSN Code of Practice for Cost Effective Boreholes. For a buyer equipping its own drilling unit, it helps separate hardware from know-how: a new rig without an experienced driller and hydrogeological supervision seldom yields good boreholes.

From Belgium, Sobetracom consults makers of rigs, compressors and casing, compares offers item by item, checks consistency between drilling diameters, casing and planned pumps, and arranges transport of carriers and long packages with the forwarder. Relays in DR Congo, Burundi, Guinea and Nigeria follow delivery; importing a registrable carrier and tooling should be prepared with the licensed clearing agent before shipment.

Frequently asked questions

What casing diameter for a borehole with a submersible pump?
The RWSN guide says 150 mm casing is generally enough for a motorised rural borehole, while 100 mm takes a handpump. Final diameter should be checked against the pump maker's curves and the target yield.
Can any PVC pipe be used as borehole casing?
No. According to PIPA note POP105, stiffness is what counts, and it depends on wall thickness. At equal pressure class, PVC-M or PVC-O does not replace PVC-U, and PVC-O is not recommended.

Sources

  1. Rural Water Supply Network, Dotun Adekile, Supervising Water Well Drilling: A Guide for Supervisors, Publication 2014-5 (édition révisée 2014) (2014)
  2. Plastics Industry Pipe Association of Australia, POP105 PVC Pipes in Bore Casings (July 2007)
  3. Skat Foundation, publication Borehole Drilling – Planning, Contracting & Management: A UNICEF Toolkit (October 2026)

This page summarises public sources as of the date shown. It does not replace the official text: check it before committing to a purchase, a bid or a shipment.

A project in Africa? Let's talk.

Tell us what you need and where it goes. We come back to you with first leads.