Sobetracom

Equipment sourcing · Industry

Industrial air compressors for sites in Africa: flow, air quality and climate

Compressed air drives much of a workshop: pneumatic tools, cylinders, blasting, painting, blow-off and sometimes air-assisted laser cutting. A poorly chosen compressor shows quickly: pressure falling at the far end of the network, water in the tools, a motor overheating in a room that is too hot.

For a buyer equipping a site in Africa, the specification has to cover the essentials: the flow actually delivered, the air quality users require and how the machine copes with heat and dust.

Updated on 20 October 2026

Compare flows measured the same way

Start from the users' combined consumption, allowing for simultaneity, and the pressure needed at the furthest point. Manufacturers then quote a flow and a power input. To make offers comparable, require those figures to be established under ISO 1217:2009, the acceptance test standard for displacement compressors, which also sets the conditions for a full performance test.

Where demand varies, a variable-speed compressor or a combination of machines avoids running a large unit off-load. Motor efficiency can be compared using the IEC 60034-30-1:2014 classes, which set limits by frequency, number of poles and output; state that the motor must be rated for 50 Hz, the frequency of the target grids.

Specify air quality with ISO 8573-1

ISO 8573-1:2010 classifies compressed air by its main contaminants, particles, water and oil, and also identifies gaseous and microbiological contaminants. Its reference volumes are stated at 20 °C and 100 kPa, or 1 bar. Giving one class per contaminant at the point of use lets the supplier size filters and the dryer; the standard refers to ISO 7183 for dryers.

A paint shop, a laboratory or a food plant have different needs from a fabrication shop. In a humid climate the water load is high, so the dryer, automatic drains and oily condensate treatment must be sized for the site's actual temperature and humidity.

Safety and pressure equipment

In Europe, EN 1012-1:2010 covers the safety of compressors with an operating pressure above 0.5 bar, from design to disposal, excluding explosive atmospheres. Air receivers fall under the Pressure Equipment Directive 2014/68/EU, which applies above 0.5 bar and entered into force on 20 July 2016. Ask for declarations of conformity for both compressor and receiver, the receiver's nameplate and certificate, and safety valve settings: these documents support periodic inspection on site, whatever the local rules.

Heat, dust and maintenance

A screw compressor turns most of its energy into heat. In a poorly ventilated room the intake temperature rises and the machine trips. Tell the manufacturer the maximum room temperature, ask for the permitted ambient range, and plan hot-air ducting and a filtered fresh-air inlet. Dust calls for an intake pre-filter and shorter cleaning intervals.

Order service kits for the first years (air and oil filters, separator, oil) with the machine, together with technician training and a maintenance plan. Sobetracom consults several manufacturers against this specification, compares offers at equal ISO 1217 flow and coordinates shipping. Import formalities should be checked with the client's customs broker before each consignment.

Frequently asked questions

Why require flow measured to ISO 1217?
Because it is the acceptance test standard for displacement compressors. Two flow figures obtained by different methods cannot be compared.
Is a dryer needed in a humid climate?
Almost always. Set the required water class under ISO 8573-1 at the point of use and let the supplier size the dryer for site temperature and humidity.
Does the air receiver need certification?
In Europe, a receiver with a maximum allowable pressure above 0.5 bar falls under Directive 2014/68/EU. Its certificate makes periodic inspection on site easier.

Sources

  1. ISO 8573-1:2010, extrait publié par iTeh Standards (October 2026)
  2. Genorma, fiche ISO 1217:2009 (October 2026)
  3. Genorma, fiche EN 1012-1:2010 (October 2026)
  4. Commission européenne, Pressure Equipment Directive (October 2026)
  5. Genorma, fiche EN 60034-30-1:2014 (October 2026)
  6. WorldStandards, Plug, socket & voltage by country (October 2026)

This page summarises public sources as of the date shown. It does not replace the official text: check it before committing to a purchase, a bid or a shipment.

A project in Africa? Let's talk.

Tell us what you need and where it goes. We come back to you with first leads.