Equipment sourcing · Industry
Welding machines for sites and workshops in Africa
Welding machines are among the items most often bought for an industrial or civil works project, and among the most often poorly specified. A machine chosen on its maximum current alone may overheat and cut out every few minutes in a hot workshop, or refuse to run from a generator.
A sound specification starts from the process and the work to be welded, accounts for site temperature and power supply, and comes with a quality framework: qualified welders, procedures and consumables.
Updated on 20 October 2026
Match the process to the work
ISO 4063, as used in EN ISO 15614-1:2017, numbers the processes: 111 for manual metal arc, 13 for gas-shielded MIG/MAG, 14 for TIG and 114 for self-shielded flux-cored wire. On exposed sites, stick electrodes and self-shielded wire tolerate wind; in the workshop, MIG/MAG gives productivity; TIG is for stainless steel, tubes and fine repairs.
The process also drives logistics: shielding gas cylinders available locally, wire and electrodes, torch parts. Before choosing MIG/MAG or TIG, check the supply of argon and gas mixtures in the site's city.
Duty cycle and temperature: reading the data sheet
Duty cycle gives the percentage of time a machine can weld at a given current without overheating. The figure only means something at a known temperature: IEC 60974-1 has required the heating test at 40 °C ambient since its 2012 edition. Ask manufacturers for the duty cycle at the current you will actually use, established under that standard, rather than the maximum current.
EN IEC 60974-1:2022 covers industrial and professional arc welding power sources supplied at up to 1 000 V, battery-powered or engine-driven, as well as plasma cutting systems. It excludes limited-duty equipment for lay users, which falls under IEC 60974-6: an entry-level machine has no place on a construction site.
Power supply: unstable grids and generators
Inverter welders are light and efficient, but their electronics dislike surges. On an unstable grid or a generator, ask the manufacturer for the permitted input voltage range, generator compatibility and the recommended generator rating. For remote sites, an engine-driven welder, covered by the same standard, removes dependence on the grid.
In dusty conditions, the enclosure's degree of protection and ease of cleaning matter. Specify welding and earth cables of the right cross-section and length, electrode holders, torches and a set of wear parts.
Quality: welders and procedures
The best machine cannot make up for missing organisation. EN ISO 3834-2:2021 sets comprehensive quality requirements for fusion welding, in workshops and in the field. EN ISO 9606-1:2017 defines the qualification test for welders on steel, recognised regardless of location. EN ISO 15614-1:2017 qualifies welding procedures, with 2 test levels, level 2 applying where the contract specifies none.
For critical work (steel structures, tanks, pressure piping), write these requirements into the site specification and plan welder training on the equipment supplied. Sobetracom compares offers from several manufacturers on these criteria and coordinates shipment of machines, consumables and protective equipment. Import rules should be confirmed with the client's customs broker before dispatch.
Frequently asked questions
- How should duty cycles be compared?
- At the same current and under IEC 60974-1, whose heating test is run at 40 °C ambient. A duty cycle stated at a lower temperature overstates the machine in a hot workshop.
- Will an inverter welder run from a generator?
- Often, but not always. Ask the manufacturer about generator compatibility and the recommended generator rating, and protect the input against surges.
- Do donor-funded projects need certified welders?
- For structural or pressure work, qualification under EN ISO 9606-1:2017 and procedures qualified under EN ISO 15614-1:2017 are the usual reference in specifications.
Sources
- Genorma, fiche EN IEC 60974-1:2022 (October 2026)
- Genorma, fiche EN IEC 60974-1:2018 (October 2026)
- Genorma, fiche EN ISO 15614-1:2017 (October 2026)
- Genorma, fiche EN ISO 9606-1:2017 (October 2026)
- Genorma, fiche EN ISO 3834-2:2021 (October 2026)
This page summarises public sources as of the date shown. It does not replace the official text: check it before committing to a purchase, a bid or a shipment.
