Sobetracom

Equipment sourcing · Raw materials

Buying cement for a construction project in Africa: type, class and storage

Cement is the most ordinary of building materials, which is exactly why it is so often badly specified. "Portland cement" is not enough: the European standard EN 197-1 describes 27 common cements, and the right one depends on the structure, the soil, the mixing water and the climate. The wrong type, or cement that picked up moisture in transit, costs strength and durability.

Sobetracom is not a cement producer. For public buyers, NGOs and contractors building in Africa, we draft the specification with the design office, approach producers whose certification can be verified, compare offers on the same designation and have packaging and documents checked before shipment. What follows draws on the standard and on producers' data sheets; the project owner's specification always comes first.

Updated on 20 October 2026

Reading a designation such as CEM I 42,5 N

An EN 197-1 designation reads from left to right. First the type: CEM I is Portland cement, with at least 95% clinker according to Vicat; CEM II covers Portland composite cements (limestone, slag or fly ash); CEM III, IV and V are blast furnace, pozzolanic and composite cements. Then the class: 32.5, 42.5 or 52.5, the minimum compressive strength at 28 days in MPa. Finally the letter: N for ordinary early strength, R for rapid, and L for low, which only applies to CEM III.

The CBR and ENCI data sheet for a CEM I 42,5 N, for instance, requires at least 10.0 MPa at 2 days and a 28-day strength between 42.5 and 62.5 MPa. An offer that simply says "42.5" without type or letter cannot be compared with anything.

Sulfate soils and coastal sites: consider SR cement

According to the abstract published by the Swiss standards body, EN 197-1 also defines 7 sulfate-resisting common cements. For Portland cement, the SR suffix carries an index linked to the clinker C3A content. Holcim's sheet for a CEM I 42,5 R-SR 5 caps clinker C3A at 5.0% and recommends it for aggressive environments, sulfates or seawater, with chlorides limited to 0.10%.

This needs settling with the design office whenever the structure meets sulfate-bearing soil, saline groundwater or the sea. The standard also notes that some countries recognise other cements as sulfate-resisting within their own territory, so the list accepted in the destination country belongs in the file. National marks matter too: in Belgium, the LA mark denotes an alkali content of no more than 0.60% under NBN B 12 109.

Certification, bulk or bags

Cement that conforms to EN 197-1 carries CE marking, and some producers add voluntary marks such as BENOR in Belgium or KOMO in the Netherlands. We ask for the declaration of performance, the notified body's certificate and the production date of each lot. Producers are compared on the same full designation, never on a trade name.

Packaging depends on the site. Bulk supply needs silos and unloading equipment on arrival; bags, such as the 25 kg sacks Holcim offers for this cement, can be handled manually but are vulnerable to damp and tearing. For a remote site, bags on shrink-wrapped pallets loaded into containers cut down on rehandling and rain exposure at each transhipment.

Storage through the rainy season

Cement that has taken on water turns lumpy and loses strength. Bangladesh's building code, written for a monsoon climate, is specific: bags on planks at least 200 mm off the floor and 450 mm from external walls, stacks no higher than 15 bags, alternate courses above 8, and the whole stack wrapped in polyethylene during the monsoon or for storage beyond 2 months. It also requires cement to be used in the order it arrives. Holcim, for its part, asks for covered, ventilated storage away from direct sun.

We write these rules into the delivery plan, so that quantities arrive at the pace of the works rather than as a single consignment left waiting for months.

Frequently asked questions

Is a CEM II cement suitable for reinforced concrete in buildings?
CEM II cements are Portland composite cements and are widely used for reinforced concrete in Europe. Whether to choose CEM I or CEM II depends on the target strength class, the exposure of the structure and the design office's specification, which sets the full designation.
How can we tell whether delivered bags have been exposed to moisture?
Hardened bags or lumps are a warning sign. The production date printed on the bag, the inspection report at loading and proper storage on site are the best safeguards. If a lot is in doubt, a laboratory strength test settles it, and compliance with the destination country's own requirements should be confirmed with the local laboratory or building control body.

Sources

  1. SNV (Association suisse de normalisation), résumé de la SN EN 197-1:2011 (October 2026)
  2. Vicat, « What are the different kinds of cement? » (October 2026)
  3. Baukobox, « Cement strength class according to DIN EN 197-1 » (October 2026)
  4. Heidelberg Materials Benelux (CBR, ENCI), fiche produit « Portlandcement CEM I » (November 2020)
  5. Holcim España, fiche technique CEM I 42,5 R-SR 5 (July 2024)
  6. Bangladesh National Building Code 2012, Part 7, Chapter 2, 2.2.1.1 « Cement » (2012)

This page summarises public sources as of the date shown. It does not replace the official text: check it before committing to a purchase, a bid or a shipment.

A project in Africa? Let's talk.

Tell us what you need and where it goes. We come back to you with first leads.